Laying a pipeline for water supply is a task no less significant than the selection and connection of pumping equipment, the arrangement of a water source. Incorrectly routed water in a private house can lead to pressure surges, disruption of the system.
To avoid problems, you need to carefully study all the intricacies of the work. We will help you by presenting complete information for studying the specifics of the device systems and assembly rules. The information proposed for consideration is based on regulatory requirements.
The detailed description of the schemes, options, and nuances of the wiring of the water supply circuit that we presented for review is supplemented by visual illustrations and video materials.
Water distribution schemes
The water distribution can be carried out in two ways - with serial and parallel connection. The choice of water supply scheme depends on the number of residents, periodic or permanent stay in the house or on the intensity of use of tap water.
There is also a mixed type of wiring, in which the faucets are connected to the water supply system through a collector, and the remaining plumbing points and household appliances are connected by the serial connection method.
Image Gallery
Photo from
Private water supply option
Coarse and fine filtration system
Manifold option of water supply
The accumulator in the water supply
Connecting water pipes to the heater
Pump station to increase system pressure
The solution for a branched and long circuit
The condition for the installation of water in a private house
Scheme # 1. Serial (tee) connection
It is an alternate supply of pipes from a riser or water heater to plumbing devices. First, common pipes are diverted, and then, using tees, they lead branches to places of consumption.
This method of connection is more economical, it requires fewer pipes, fittings, it is easy to install. Pipe wiring with a tee system is more compact, it is easier to hide under finishing materials.
With a sequential scheme for connecting a pipeline with hot water, the discomfort is especially noticeable - the temperature of the water changes dramatically if several people use the water supply at once
But serial connection is more suitable for municipal apartments, for houses with periodic residence or with a small number of residents. It cannot provide uniform pressure in the system when it is used by several users at the same time - at the most remote point the water pressure will change dramatically.
In addition, if you need to repair or connect a plumbing fixture, you will have to disconnect the entire house from the water supply. Therefore, for private houses with high water consumption and permanent residence, it is better to choose a scheme with parallel wiring of the water supply.
Image Gallery
Photo from
The principle of tee water pipe assembly
Pipe Connection Features
Minus tee pipe routing
The way to solve problems with pressure
Scheme # 2. Parallel (collector) connection
Parallel connection is based on the supply of individual pipes from the main collector to the water intake points. For cold and hot lines, they install their collector nodes.
This method requires laying a large number of pipes and, accordingly, creates difficulties in masking them. But then, each point of the draw-off will have a stable water pressure, and with the simultaneous use of several plumbing fixtures, changes in the water pressure will be insignificant.
Image Gallery
Photo from
Benefits of Collector Wiring
The principle of the construction of the collector circuit
Disadvantages of the collector solution
Equal pressure at all points
A collector is a device with one input for water and several conclusions, the number of which depends on the number of plumbing units, household appliances that use tap water for work.
A collector for cold water is mounted closer to the pipe inlet to the house, and for hot water it is mounted at the outlet of the heater. A purification filter and a pressure regulating pressure reducer are installed in front of the collector.
Each output from the collector is equipped with a shut-off valve, which allows you to disable a specific point of water intake, while the other conclusions will work in normal mode. In addition, each of them can be equipped with a regulator to maintain a certain pressure for individual devices
Water separation
Installation of a hot water supply system and a cold water supply system can be carried out in two ways:
- With a "deaf" wiring. The water supply pipe to the last water intake point ends in a dead end. Such a scheme is more beneficial for saving space and from an economic point of view, but can create inconvenience in the operation of the water supply system. Water in the last node will come with a delay, and only after it reaches the plug, it will begin to flow into the tap.
- With closed circulating wiring. With this method, water constantly moves in a circle, has the same temperature at each point in the system, and comes to the user immediately after opening the tap. It is advisable to use the peculiarity of this wiring method specifically for a hot water supply system - it is important to prevent sudden temperature jumps in it.
In order not to unnecessarily complicate the water distribution in the house, it is more rational to use the combined version. The cold water supply system is performed using a blind wiring, the hot one is circulated.
On a simple diagram, the differences of different water supply schemes are immediately visible: 1 - standard, “deaf”; 2 - with forced circulation; 3 - "deaf" using a collector
How to make a project yourself?
In order to properly plan the water supply system, you must first draw up a plan of the house, placing all the plumbing devices in it, equipment that will be connected to the water supply.
All sizes are indicated on a single scale, according to the actual measurements of the premises. The more accurately the plan is drawn up, the more accurately it will be possible to determine the required amount of materials and components.
The water supply scheme should as accurately as possible reflect all the points of water intake, the length and location of pipes for transporting water, and even sewage, as these communications are often carried out nearby. The number of filters, boiler volume, and pumping equipment parameters are also taken into account.
The wiring diagram should be simplified as much as possible, trying to avoid pipe intersections. Water pipes are placed closer to the sewer to hide them with a common box. When placing pipes under the floor, the tees lead straight up
The project must take into account the requirements of construction standards, as well as the rules of water supply and sanitation, approved and in force in the country.
Installation of water supply system nodes
A typical wiring diagram of a water system with a well or a well can be used for serial piping.
It consists of the following nodes:
- Pump equipment. For a deep well of more than 8 meters or a well, only a submersible pump is suitable. For shallow sources, assembly stations or surface pumps can be used.
- Transitional nipple. It is necessary for connection with the following elements of the system, which in most cases have a diameter different from the output from the pump.
- Check valve. Prevents leakage of water from the system when the pump is idle, water pressure drops.
- Trumpet. Pipes made of polypropylene, steel, metal-plastic or other materials are used. The choice depends on the wiring (external or internal, hidden or open), the price of the material itself, ease of installation. The pipeline supplying water to the house is provided with a heat-insulating layer.
- Water folding fittings. It is used to connect pipes, shut off water supply, install the pipeline at an angle, etc. It includes: fittings, taps, water sockets, tees, etc.
- Group of filters. Designed to protect equipment from ingress of solid and abrasive particles, reduce the iron content in water and soften it.
- Accumulator tank. It is required to create and maintain a stable pressure of water, to prevent frequent operation of the pump.
- Security group. It is necessary to control the pressure in the system - pressure switch, pressure gauge and dry run relay. Automatic control devices help maintain a stable pressure in the system and extend the life of the equipment.
All elements of the system are connected in a certain sequence. More details can be considered in the diagram. Next, the installation of the system is described by the example of collector wiring, as more complex.
A simple diagram of the water supply system makes it possible to imagine how wiring should be carried out from the source to the extreme point of consumption (+)
The collector unit in a private house is installed in special rooms - boiler rooms or boiler rooms - specially allocated rooms of a residential building, in basement and semi-basement rooms.
In storey buildings, collectors are installed on each floor. In small houses, the system can be placed behind the flushing tank in the toilet or hidden in a special cabinet. To save water pipes, the collector is positioned closer to a larger number of plumbing fixtures, at approximately the same distance from them.
Installation of the collector assembly, if you follow the direction of the water, is carried out in the following order:
- At the junction of the collector with the main water supply pipe, a shut-off valve is installed to shut off the entire system if necessary.
- Next, a sediment filter is mounted, which delays large mechanical suspensions that can lead to equipment breakdown.
- Then another filter is installed, which will remove smaller particles from the water (depending on the model, particles from 10 to 150 microns).
- The next in the installation diagram is a check valve. It blocks the reverse flow of water when the pressure drops.
After installing the above equipment, a collector is connected to the water supply pipe with so many conclusions that corresponds to the number of water consumption points in the house. If not all plumbing fixtures are connected in the house, then plugs are placed on the unclaimed conclusions of the collector assembly.
The installation of the water supply branches of the hot and cold water system is the same for central water supply. Installation in a house is a little different: one of the collectors' cold water outlets is connected to a water heater, from where hot water is sent to a separate collector unit
Laying methods - hidden and open system
Pipes in the water supply system can be laid in a closed and open way. The choice of one of the methods does not affect either the quality of the connections or the functionality of the entire system and depends only on personal preferences.
It would seem that it is easy to determine and a closed method is preferable as more aesthetic and allows you to save up to 10 cm of usable space. Why is an open pipeline still used in the installation of a water supply system? Let's try to give an answer.
Image Gallery
Photo from
Plumbing pipes
Polypropylene water system
Water supply device with water pipes
Water pipes made of copper and stainless steel
Hidden wiring allows you to hide pipes and not spoil the aesthetic perception of the interior of the house or apartment. The hidden method is used when assembling a water supply system from PP pipes. They hide the contour behind a decorative wall, for example, from drywall, or ditch the walls and pipe into the formed niches, covering them with cladding material or plaster on a grid.
The pipeline should not adjoin tightly to surfaces - always leave a small gap for possible repair. When installing the pipeline in a monolith, it is recommended to place them in the casing, inserting the pipe into the pipe.
The disadvantage of the method is manifested when there is a need to repair or replace hidden elements of the system - the plaster or tiling must be opened, and then re-decorated.
In addition, in case of damage and leaks, the problem may not be detected immediately and lead first to a loss in the operational technical characteristics of the structures, then to flooding of the premises.
It is better to proceed with the installation of a water supply system with a pre-compiled diagram - otherwise, errors in the calculations or assembly will lead to the fact that you will have to ditch new grooves and re-install pipes
To avoid such difficulties, when installing the wiring, only whole sections of the pipe are hidden, placing the fitting in open areas. In places of installation of shutoff valves make inconspicuous doors. This gives service access to pipe connections, which are the weakest links in the system.
It should be noted that pipes of not all materials can be hidden under a layer of plaster - for this, only products made of polypropylene, metal-plastic or copper are suitable.
Open pipe laying is carried out after finishing. The method involves laying bare pipes and water supply elements in no way. It looks ugly, reduces the usable area of the room, but at the same time this method is very convenient for maintenance, repair and dismantling of elements.
Redevelopment and rearrangement of plumbing in the house with such a plumbing arrangement will also not cause difficulties.
Open wiring makes it possible to quickly detect a leak and eliminate the cause of breakage or damage to system elements
General installation tips
Before mounting the pipeline, it is necessary to install all the fasteners and finish welding work. Pipes that were stored or transported at sub-zero temperatures before laying can withstand at least a day at temperatures above 10 ° C. Before starting the installation, it is necessary to align them and in the future not to allow deflections.
Pipes to walls and supports are fixed with clamps or hooks. The distance from the fasteners to the threaded connections should be more than 5 cm
For water risers use pipes with an outer diameter of at least 20 mm, for floor wiring - with a diameter of 16 mm and 14 mm. It is better to use as few collapsible joints as possible. It is necessary that all connecting elements correspond to the type (series) of pipes and, as well as fittings and revisions, are in accessible places.
Horizontal sections of the water supply system should have a bias towards the drainage valves to allow water to drain, lift to the side of the device through which air will exit when the system is filled with water. When installing vertical structures do not allow their inclination more than 2 mm per meter.
Carrying out vertical installation of the pipeline, hot water pipes are placed to the right of the cold water pipes. With horizontal wiring, cold water supply is placed below under hot water to prevent condensation.
They close the channels or monopolize the pipeline only after a trial run of the system and checking its operability, leaks and damage
During operation of the hot water supply, a phenomenon such as thermal expansion occurs, which is especially characteristic of polypropylene products. At the same time, the pipes can lengthen, this leads to damage and leaks.
The correct arrangement of fasteners and self-compensation of such sections of the pipeline as bends, turns, gaskets "snake" prevent deformation.
Clip # 1. Distribution of the HVS and GVS systems in the two-story house:
Clip # 2. Features of the installation of hot water and cold water in the house:
Clip # 3. How to mount the collector assembly compactly:
You can install the wiring in your own house yourself, but to avoid unpleasant consequences from unprofessional work, it is better to ask a specialist to help design the system. Professional advice will help to avoid mistakes, unnecessary expenses and alterations.
Do you have questions in the process of getting acquainted with the material? Do you want to share personal experience or provide interesting information on the topic? Please comment in the block below the text of the article.