There are a number of good reasons for replacing a gas hose, including banal sleeve wear. According to technical standards, to perform this work it is necessary to call an employee of the gas service. But what to do if the need arose in a country house, for example, where you can not hope for the prompt arrival of gas workers? Act on your own!
However, you should first understand the technological nuances according to which this work is performed. We will tell you how to replace a gas hose with your own hands. Using the information, you can correctly remove the old sleeve and install a new one, without fear for the safety of the family and neighbors.
We have described in detail all types of hoses approved for use in the gas industry. As an example, the installation process of a new gas stove with a full range of equipment is given. The information presented for consideration will be useful both to those who decided to independently perform the replacement, and to customers of gas services.
Types and features of gas hoses
After acquiring a new gas stove or when replacing old equipment, a change in flexible hose will be required. On sale you can find only five types of these communication devices, but they are not popular.
The reasons for the low level of demand for certain types of gas hoses lie in the complexity of the installation work. And in some cases, you can’t do without calling a specialist.
The most popular flexible models include such eyeliners:
- rubber;
- rubber fabric;
- rubber reinforced with metal threads;
- bellows metal.
In addition to flexible models, you can find steel and copper pipes. The requirements for connecting this type of sleeve are very different in comparison with flexible models.
The methods for soldering copper pipes also differ. If the installation is carried out by brazing, it is necessary to use exclusively copper-phosphorus contacts PMFS6-0.15 and PMFOtsr6-4-0.03. Soft soldering in this case is not allowed.
When installed by brazing, one of the important conditions is to maintain the temperature regime not exceeding the 600 ° C mark. For soft soldering this range is reduced - no more than 400 ° C
Another way to contact gas pipes is to install copper fittings by extrusion. Compression fittings for hoses are selected based on the pressure coefficient of the pipe. If the diameter of the pipe is not more than 54 mm, a fitting-free connection method is allowed.
On fittings for crimping a gas hose, most often, you can see a yellow marking. In some cases, only the seal ring is yellow. It is worth considering that the use of shortened fittings is strictly prohibited
Despite the reliability of connecting such hoses to gas appliances, they have several disadvantages:
- install without special equipment will fail, so you will need to call a specialist;
- the placement of the plate will be stationary, without the ability to move;
- laborious installation process.
Such methods are used infrequently and are unreasonably costly. Financial investments will be many times higher than when using popular flexible hoses. And it is also worth considering the duration of the work - at this time there will be no access to gas supply.
Features of rubber sleeves
A rubber hose designed primarily for transporting oxygen is considered a rare option, although you can easily find it on the market. He has many advantages: pressure retention of 20 atmospheres, affordable price, ease of installation and good electrical insulation.
However, despite all the positive qualities, the device requires special vigilance during operation. The contact of a portion of the surface of the sleeve in contact with air and the smallest drop of oil can lead to overheating of the hose, and, accordingly, to a quick failure.
Using a rubber hose as an associated gas equipment is an inappropriate use of this type of hose. Despite its positive characteristics, it needs to be carefully and constantly inspected during operation.
It is worth abandoning the use of an oxygen sleeve - it is considered a relic of the past when there were no more advanced and safe products. Its installation in the kitchen of an apartment of a multi-storey building is especially dangerous - the owner risks not only his life, but also a hundred unsuspecting people about anything.
If in the country, i.e. the place of temporary location, such a product is used, you need to be especially careful and pay attention to its marking, where the following parameters should be indicated: product class, internal diameter, maximum allowable pressure.
A visual inspection of the presence of defects in the form of blisters, cracks and punctures of the fiber frame will also be required - the presence of exposed areas is not allowed.
Rubber product specifications
Good recommendations deserved rubber hose. This is ease of use, inexpensive price, high coefficient of flexibility, rich size range (almost any length and diameter), excellent electrical insulation.
The disadvantages include the weak stiffness of the material - the product is made from rubber reinforced with fabric threads. Despite this, modern technologies used to make the model will help to last up to 10 years.
Rubber-fabric gas hose is the cheapest of all options for accessories. Due to the extensive size range, it is possible to choose the required sleeve sizes
Another negative quality is that after a short period of time cracks appear in the rubber, which are conductors of gas leakage. Despite the good strength indicators, experts do not recommend using such a hose for more than two years. This type of eyeliner is in demand for gas cylinders in a private house.
The specifics of reinforced eyeliner
The type of product reinforced with a metal mesh has much in common with water pipes - a thin-wire braid of steel gives structural strength. Two fittings and threaded rivets located at the ends of the sleeve, act as fasteners for the hose and gas stove.
A clear advantage of this type of connection is reliability. And to ensure its safety, it is necessary to put dielectric inserts between the hose and the stove. In addition, when installing necessarily use gaskets made of copper, aluminum or other soft metals.
Today, manufacturers produce reinforced hoses with fittings made of an alloy of iron and carbon or brass. It is worth giving preference to these materials, excluding stainless steel.
Reinforced sleeves are inexpensive and easy to use. The flexibility of rubber and the strength of the metal were successfully combined in this product, which served to increase its popularity for use in domestic conditions. Experts in our country recommend gradually abandoning their operation in favor of a more advanced option.
Reliable bellows metal joint
The most reliable and durable option is a bellows metal hose. It is used to connect the stove to the gas line, has a high coefficient of flexibility, which is achieved due to the corrugation made of stainless steel.
Moreover, at the time of bending, there is no deformation of the inner section of the sleeve. The hose can be extended up to four times. All this is reflected in its price category - the cost of the product is quite high.
The service life of the bellows metal liner reaches 25 years. When mounting on a stove with electric ignition, electric grill and backlight, a dielectric insulating gasket is required between the sleeve and the gas tap
The standard lengths for this type of hose are 1.5–2 m, thread diameters are ½ or ¾ inch. Due to the method of fixation, hoses with fastening “nut-nut” and “nut-fitting” are distinguished. In addition to a well-bending surface, they are able to withstand pressure of 6 atmospheres, and can also come in contact with temperatures from - 50 to +200 ° C.
The only drawback is the price category, which exceeds five times its competitors.
Flexible bellows gas hoses are equipped with a protective polymer shell on the outside, which protects the sleeve from corrosion and prevents damage
Flexible bellows hoses are divided into ordinary and with a metal base made of stainless steel. The latter are protected by a two-layer polymer coating, which provides high-quality electrical protection. It protects the material from corrosion and acid exposure, as well as from the high temperature regime of the furnace device.
The manufacturing material for this type of gas liner is stainless steel, which meets all the technical requirements of GOST. Due to the polymer coating, the product is protected from various forces.
The sleeve provides a guarantee of the integrity of the gas supply system for a long period - up to 25 years. The electrical resistance of the material reaches 1500 V, which is important, because modern stoves are equipped with rich electrical functionality.
The bellows hose has a polymer coating to insulate the gas stove, equipped with electrical functions: ignition, backlight, grill
Gas hose selection rules
Any equipment, including the connection for blue fuel appliances, must have a quality certificate guaranteeing the specified service life.
To purchase this kind of product is necessary only in specialized stores. Do not forget about the differences between a water hose and a gas hose: a yellow mark on the braid indicates that you have a sleeve for gas in front of you, blue-red for water supply.
Details on choosing a hose for connecting gas equipment are written here. We recommend that you familiarize yourself with the article we have proposed.
Connection Security Basics
Any gas equipment, including related equipment, must be connected in compliance with safety rules. Gas is an explosive substance, with which you should be as careful as possible.
This requirement also applies to devices for its supply, which must be of high quality and provide an appropriate level of protection:
- It is not recommended to hide the gas hose; it is important to ensure access to it.
- The product cannot be painted.
- When installing, pay attention to the sleeve tension - it should sag a little.
- During installation, do not bend much and give in to twisting of the eyeliner.
- The metal parts of the product must be protected against condensation.
For installation of a flexible hose, only tools, materials and accessories intended for working with gas equipment are used. Particular attention should be paid to this, because many details are almost identical to materials for water supply.
Gas stove connection diagram
Schematically, the connection of the stove to the gas is as follows: a gas riser passes through the kitchen room, from which a branch pipe with a tap at the end, connected to the furnace, leaves. This piece is also called a lowering or retraction.
In old houses, a petal-type crane is installed on the edges. When reconnecting, it is recommended to replace it with a ball. It takes up less space and is more convenient to use.
A rubber-fabric hose is screwed into the tap through which gas is supplied. For old houses, a plate is planted on a metal pipe. This method is not practical to use, because in this case the location of the device will be stationary.
In remote areas of the private sector, where there is no access to the laid main gas pipeline, gas is used in cylinders. Only a gas service specialist is allowed to connect to such equipment.
Self-Instruction
Payment for gas services for installation works is not too high, but many home masters prefer to do everything on their own. This is a feasible occupation that requires the purchase of components and theoretical knowledge.
And to connect, you will need to prepare the following tools and buy materials:
- keys: gas No. 1, adjustable 22-24;
- screwdriver to tighten the clamp, if required;
- seals (thread loktayt 55, flax, FUM - tape);
- gasket ½;
- gas hose;
- ball valve 1/2 ′;
- a brush and soap solution, which will be required to control the execution of work.
A rag and a plastic cork are also useful. The rag will be used as a temporary cover against gas leakage. The narrowed edge of the plug must be fitted to the opening of the feed pipe. If during the extraction process, a home-made part gets stuck, it can be easily removed with a corkscrew.
Step # 1: Removing the old plate
Overlapping the crane at the lowering is a priority for ensuring the safety of the work performed. Next, it is necessary to unscrew the lock nut located on the branch and remove the coupling. If at the old plate the coupling and locknut were previously painted - this will greatly complicate the process of dismantling them.
Sometimes this procedure fails, then you need to cut off the eyeliner with a grinder.
The gas stove is dismantled after disconnecting from the conductor pipe of the gas main. Any difficulties with unscrewing the lock nuts on a metal pipe are solved by cutting the eyeliner
In the process of unscrewing the drive located in the lowering valve, the tap itself must be held by the key. It will not have to be removed unless replacement of the crane is planned. When they plan to wait a while with the installation of the slab, an additional plug is installed on the lowering.
Step # 2: Perform a tap replacement
There are situations when the wall is located in extreme proximity to the crane and there is no way to dismantle it. In this case, it is necessary to bend the mount and install a wedge between the wall and the pipeline. However, this is done so that there is an opportunity to continue to do the work.
It is necessary to prepare a piece of rags sufficient to completely block the pipe after dismantling the old crane. The next will be its tearing off without full unwinding. And you also need to prepare the selected type of seal. Do not forget to carefully ventilate the room during operation to eliminate gas vapors.
After unscrewing the faucet, the exit from the pipe is tightly fixed with a finger, and then with a wet rag. The main actions are aimed at the maximum elimination of gas exit from the pipe. In this case, the thread on the branch should not be closed, since it will be covered by the selected sealant.
Before winding the seal, the thread on the lowering must be thoroughly cleaned. Further, its winding is carried out directly. This process provides a reliable and tight fixation of the new faucet, which then tightly twists. The last step is to install the previously removed handle on the tap.
Using soapy foam, the tightness of the faucet and gas pipe connections is monitored. If the work was done correctly, the installation of the gas hose can continue
If for the first time gas equipment is connected to a gas main, it is necessary to call a gas master.In his presence, a check is carried out of the equipment for gas leaks with the valve open. In the event that the employee of the gas service has not found any violations, he must enter in the register the established brand of the stove.
Step # 3: Connect the flexible hose to the plate
An outer thread of the hose fitting is wrapped with a sealant. After that, it must be screwed into the tap on the branch pipe. The flexible hose is connected to the collector at the finish stage.
Further, the mandatory stage of the test opening of the tap on the lowering for gas leaks. Using soap suds, the joining points are processed with a brush. If foaming occurs when the gas valve is opened, the work must be redone.
It is necessary to verify the threads located on the plate header. Quite often it is 3/8 ′. In this case, you need to install the adapter to 1/2 ', with a sealant
If the work on replacing the gas hose is carried out in a private house where balloon gas is used, an additional nozzle replacement with a smaller diameter will be required. If this is not done, the burners will release too much soot, which likes to settle on furniture and utensils in the kitchen.
Need to Know: Valuable Tips
Before acquiring a flexible hose, it is necessary to verify the dimension of the thread at the outlet of the plate, its classification and whether it is a straight or angled type. If the outlet is of direct type (directed towards the wall), it is necessary to purchase a sleeve with a square at the end.
The gas hose must not be painted - this will accelerate its cracking. A more attractive look can be created by pasting with special paper or oilcloth.
And it is strictly forbidden to tightly sew up gas lines with false panels made of drywall and other structures - this will make it difficult to carry out service work with individual elements.
To camouflage the gas supply system, a collapsible box is used, which can be easily dismantled if necessary. In this case, all structural elements of the gas system will have constant access.
It is forbidden to use extra connections. Independent complication of the gas structure, according to the technical regulations, may result in a fine or disconnection from gas supply
If a master was called to connect a gas water heater or stove, it is necessary to check the correctness of the work: the excess bend from the tap on the lowering must be unscrewed, the flexible wiring is directly connected exclusively with a tap located on the branch pipe, and its other end only with the gas stove outlet .
And also the use of an adapter is allowed. Any additional installation is prohibited.
Video recommendations on the choice and rules of operation of gas hoses:
Video with recommendations for installing purchased hoses:
The correct connection of the gas stove, in accordance with the necessary technical standards, is subject to mandatory verification by the gas control service, especially if the stove is new and this is done for the first time.
If a person has never encountered such kind of work, and his knowledge is extremely superficial, the best option would be to consult a specialist.
Do you have useful information on the topic of the article? Want to talk about how you changed the gas hose in your home? Please write comments, ask questions, share your opinion and photos in the block below.