Proper arrangement of a warm floor involves the most efficient use of thermal energy. To increase the efficiency of the heating system, various heat-saving techniques are used.
One of the main aspects is the insulating substrate under the warm water floor, redirecting heat fluxes from the water circuit to the finish coating. We will examine in detail the features of each type of thermal insulation damper, the intricacies of the selection and installation of bedding material.
The value of the thermal insulation substrate
Insulating material - an intermediate layer between the subfloor and the water pipe with a coolant. The main purpose of the substrate is to save and redirect heat flows upward, that is, to the living area of the room.
In addition to the task of preserving heat, the intermediate layer performs a number of no less significant functions:
- Waterproofing. In emergency situations, the waterproof substrate will hold water, protect the lower layers of the underground “cake” and prevent water from leaking to the basement. In addition, it eliminates the entry of moisture vapor from the screed to the finish floor.
- Thermal insulation. The interlayer acts as a kind of barrier between elements with different temperatures. Otherwise, contact with a cold floor will contribute to condensation and reduce the characteristic qualities of the insulation.
- Uniform heat distribution. The substrate minimizes the likelihood of obvious temperature differences - there are no excessively warm or cold zones. This feature reduces the negative thermal effect on the finish flooring, appliances and furniture.
- Sound barrier. Most lining materials absorb the sound effect of walking on the floor and improve the overall soundproofing of the room.
The substrate softens the shock loads on the base, distributing pressure pointwise - this helps to maintain the integrity of the screed.
The insulating layer, due to the low thermal conductivity of the material, gives a heat-reflecting effect - the main flow of heat energy rushes up. In the absence of a substrate, the efficiency of the heating circuit decreases sharply, and energy bills increase (+)
When arranging a water floor, the substrate is usually laid on a heater for maximum heat storage - the “thermos effect” is implemented, which reduces heat loss.
The lining with the hoods facilitates installation - you can use different options for placing the heating circuit, choosing the optimal places for connecting the system and installing control sensors
Litter Material Requirements
The characteristics of the substrate are selected depending on the type of rough foundation, topcoat and operational features of the water floor. However, there is a basic list of properties that any type of bedding material must comply with.
Strength and resilience. As a rule, the heating circuit is embedded in a cement-sand screed. A considerable load on the substrate is also exerted by the pipes of the water system, especially made of metal.
The lining material must not be irreversibly deformed, bent and change its thickness. It is important that the substrate has the ability to restore its original shape after stress relief
Low thermal conductivity. Optimally, if the heat capacity of the material is combined with its insignificant thickness. The water floor system reduces the height of the room, depending on the type of substrate, the size of the "pie" can be 5-15 cm.
A positive effect is provided by the heat-reflecting ability of the substrate, which ensures the presence of a foil film having reflex properties.
High waterproofing properties. An important characteristic is the percentage of maximum water absorption. The material should not absorb and let moisture pass through it.
Permissible water absorption coefficient - not more than 2-4%. The use of such a substrate is permissible if the material is able to completely dry without dismantling the floor - exclusively due to natural ventilation
Resistance to temperature differences. The declared properties of the substrate should be maintained at different temperature conditions. When choosing, it is important to evaluate such an indicator as permissible operating temperatures. The value of the boundary value is not less than + 70 ° С.
In addition to the indicated requirements, the substrate should not emit toxic, harmful substances. The undoubted plus is the low price, ease of installation.
Practical to use - puzzles. Mats are assembled into a single canvas by type of designer - this makes it possible to easily adjust the heating circuit to the configuration of the room
Types of substrates: assessment of properties and characteristics
Various thermal insulation materials to one degree or another comply with the listed requirements. More than others, slab polystyrene is closer to the ideal. However, in some situations it is wise to use alternatives: foil foamed polyethylene foam, cork backing or moisture-resistant chipboard.
Expanded polystyrene boards - one-stop solution
Expanded polystyrene is the result of industrial foaming of polystyrene. The finished product contains 2% of the main component with auxiliary additives and 98% of gas. The air is enclosed in hermetically sealed cells, which allows the material to maintain good temperature.
The thermal conductivity of polystyrene foam with a thickness of 10 cm is equivalent to a layer of wood of 0.35 m, of reinforced concrete and brick walls - 4.8 m and 1.5 m, respectively.
The production of expanded polystyrene by extrusion allows to obtain a substrate of high physical strength and density. Closed cells and minimal pore volume ensure water resistance of the material
Technical and operational characteristics of expanded polystyrene:
- Thermal conductivity is 0.028-0.034 W / m * K. The value of the indicator is directly proportional to the density of the insulation.
- Water permeability varies between 0.019-0.015 mg / m * h * Pa. Extruded material is molded by extruding a polymer melt through a slit nozzle.
- Moisture absorption dense polystyrene foam is 0.4%, which is 10 times less in comparison with conventional polystyrene foam. The thermal conductivity of the substrate is maintained even with constant exposure to moisture.
The compressive strength of extruded polystyrene with linear deformation of 10% is 0.25-0.50 MPa, depending on the grade of material.
Foam polystyrene mats are available in a form convenient for assembly. Smooth execution of the coating is possible with pimples for fixing the heating coil
Weaknesses of polystyrene foam: relatively low sound insulation ability and combustibility. The substrate is afraid of solvents, acetone, turpentine and kerosene - under their influence, the material is deformed.
For thermal insulation, do not choose unpressed or autoclaved polystyrene foam. These species are more fragile.
Extruded or pressed foam mats are suitable as a substrate for a water floor heating - their thermal conductivity is approximately equal. Penoplex thermal insulation is popular with consumers.
Cork material - environmental friendliness
The cork lining is made from crushed, pressed wood bark granules using various binders. The main argument in favor of such a substrate is naturalness and absolute environmental friendliness. The material is hypoallergenic and harmless to health.
Additional benefits of cork:
- resistance to deformation - after short-term shock loads it returns to its original form;
- porosity provides high sound absorption properties;
- good thermal insulation characteristics;
- convenience of cutting, styling.
Cork damper is implemented in the form of rolls and individual sheet panels. Products differ in the thickness of the pad: rolled material - 2-4 mm, cork mats - 4-10 mm.
Substrate characteristics: compression resistance under pressure of 7 kg / cm2, deformation up to 10%, material moisture content - about 7%, sound absorption coefficient on a ten-point scale - 8.5
Disadvantages of cork backing:
- vulnerability to moisture;
- exactingness to waterproofing the rough floor;
- sensitivity to high static loads.
The classic version of the cork substrate is better not to use under the water floor system. For these purposes, a rubber-cork coating is suitable, where rubber acts as a binder. In addition to water resistance, the damper has improved characteristics of sound and vibration isolation, but it can no longer be called completely natural.
Bitumen-cork substrate (2), unlike rubber-cork (1), is unsuitable for residential premises. The material is characterized by excessive toxicity and flammability.
Features of foam polypropylene damper
The simplest and most affordable solution is a polyethylene foam backing. The material is produced by extrusion of polyethylene granules, followed by heat treatment and pressing. The result is an elastic web filled with many air pores.
Depending on the structural features, polyethylene foam substrates are classified into two groups: non-crosslinked and crosslinked.
Non-cross-linked polyethylene foam consists of gas-filled cells up to 3 mm in size. The thickness of the substrate varies from 0.8 to 6 mm, the width of the roll is 1-1.5 m.
The main advantages of such a substrate include:
- high moisture resistance - water absorption of not more than 1%;
- small thickness;
- low cost.
However, non-cross-linked polyethylene foam has more drawbacks. The material is short-lived, quickly wears out, is pressed under the weight and, over time, loses its flexibility. The thermal conductivity is 0.55 W / (m ° C), which indicates insufficient heat conservation.
Crosslinked polyethylene foam (2) has a molecular structure much denser than that of an uncrosslinked fabric (1). In the manufacturing process, cross-links are formed that reduce the size of the air pores
Crosslinked Polyethylene Foam has the following features:
- phenomenal strength;
- increased density - 33 kg / cubic meter, a similar indicator of cross-linked polyethylene - 25 kg / cubic meter;
- high level of noise absorption - up to 18 dB;
- low level of thermal conductivity - 0.031 W / (m ° C);
- output format in rolls and mats, the thickness of the finished product - 1-20 mm.
The life of the substrate reaches 15 years.
Minus of “stitched” modifications: high cost. The most popular brands of foam backing: Polyfom, Tatfoum, Penolon-R, PPE-Isolon, Isolon-500
Heat-reflecting metallized substrates
Foil substrates are widely used. Moreover, a different material can be used as a base: extruded polystyrene plate, its non-extruded sibling foam, cork material or polyethylene foam.
In each case, a metallized film improves the initial technical characteristics of the base and complements it with reflex qualities.
The reflective outer coating is made of aluminum and lavsan. The thickness of the foil layer determines the degree of heat reflection of the insulation.
Lavsan or metallized film increases the efficiency of the "water floor" up to 94-98% and ensures uniform redistribution of heat. The coating is resistant to deformation and quietly tolerates high loads.
Lavsan is resistant to aggressive environments - the material retains the reflective ability and functions of the hydraulic barrier during prolonged contact with a concrete screed.
Worthy representatives of the heat-reflecting substrate based on polyethylene foam: Penofol, Isoflex, Ecofol. Foamed insulation based on polystyrene foam - Sunpol.
OSB and chipboard - “dry” laying technology
Chipboard materials play the role of a substrate when arranging a warm floor using Finnish technology. The method allows to abandon a monolithic concrete screed.
The essence of the method: the water circuit is laid in the prepared channels. The stiffness of the base is ensured by solid chipboards or a system of rails bonded to wooden lags
The floor on a wooden base has a number of features:
- ease of assembly;
- high strength characteristics;
- environmental Safety;
- universality - suitable for decoration with various flooring.
The weak side of the particle board is moisture susceptibility. To increase the hydro and thermal insulation indicators between the pipes and the wooden base, it is recommended to lay a thin substrate, the best option is foil polyethylene.
Substrate selection by type of substrate
Physical features of decorative flooring significantly affect the choice of linear parameters and physical qualities of the substrate. The greater the weight of the finish, the stronger and more reliable the damper should be.
Ceramic tile. The water floor under the tile is equipped with concrete technology - the circuit is mounted under a monolithic screed. This method is associated with significant loads on the lining material.
High support substrates, such as extruded polystyrene foam, are suitable. You can use both smooth mats and a cover with protrusions
Laminate. The main criterion for choosing a substrate for a warm water floor with a laminate coating is the highest possible heat saving rate, since the panels themselves do not allow heat to pass through well.
The light weight of the laminate does not exert significant pressure on the "water system". This makes it possible to use different types of pad, including soft ones.
The optimal solution is heat-reflecting insulation with a low degree of thermal conductivity.
Linoleum. Installation of the roll coating is carried out on gypsum board, OSB or sheet plywood. The panels have an impressive weight, which means that the requirements for the strength of the substrate are tightened. It is recommended to give preference to polystyrene, cork options or a backing made of cross-linked polyethylene foam.
Read more about the installation of a water heated floor under linoleum is written in this article.
Laying technology: a set of basic rules
Mounting the substrate does not present any difficulty, the work can be done independently. The main thing is to follow simple and clear rules.
The laying procedure depends on the form of execution of the liner: roll insulation, individual modules or slabs-puzzles, fixed to each other by a lock connection
General requirements for mounting the substrate:
- Accurate calculation. It is necessary to determine the amount of material in advance, taking into account the standard sizes of the pad. Optimally, if the insulation is placed with a minimum number of joints.
- Subfloor preparation. The base should be flat. You should not particularly rely on the ability of a dense material to mask irregularities - any product will eventually take the form of a base.
- Waterproofing. The linings of natural components (cork substrate, chipboard, OSB) require prior installation of the hydrobarrier. Enough to lay dense polyethylene.
- Stacking. Rolled, sheet material is rolled without tension, obligatory overlap on the walls. Plates are placed close to vertical surfaces protected by 10 cm damping tape.
- Docking. Cloths of rolled insulation are overlapped and fixed among themselves with construction tape. Plates and mats are grouped end-to-end.
When arranging a warm floor under a laminate, it is necessary to take into account the orientation of the panels - they are placed mutually perpendicularly with the roll substrate.
When choosing a substrate, it is better to give preference to products of famous brands. Among the popular brands, both domestic and foreign companies have proven themselves well.
The device of a warm floor using extruded polystyrene "Penoplex":
Placing the Izolon-500 foam backing under a floating warm floor:
General recommendations for choosing a heater for laying the water circuit:
The value of the insulating substrate under the underfloor heating is difficult to overestimate. The efficiency and profitability of the heating system largely depend on its quality, as well as its compliance with the flooring and the technology of placing the "water coil".
Looking for a substrate for a water heated floor? Or is there experience in installing and using a certain type of thermal insulation litter? Please leave comments on the article, ask questions and participate in discussions. The contact form is located below.