You habitually loaded the laundry, turned on the machine, she took water and started to work. But after some time she suddenly stopped. The program is not completed, things are inside, panic is approaching, the world is turning over at the mere thought of hand washing.
We will figure out how to get rid of breakdowns if the drum of the washing machine does not spin - the causes, consequences and solutions to the problem.
What can be done right away?
Calm down, turn off the machine with a button on the panel and pulling the cord from the outlet. We cover the floor with rags, we find a drain filter on the front panel from the bottom, put a container under it (a scoop, a suitable container), open it and drain the water. We take out the clothes from the machine and understand further.
Determine when the drum stopped. If, during the spin cycle, the laundry in this case remains simply wet, with no signs of soapiness. If when washing, things will be in powder.
You need to try to scroll the drum by hand. Did not work out? A foreign body or a failed part physically interferes with the rotation. When the drum spins with the machine turned off, the reason is hidden in the electronics.
The drain filter plug is unscrewed counterclockwise, and if you cannot pull it out by hand, you can use pliers
And one moment. A common consequence of drum immobility is normal overload. Try splitting the laundry in half and restarting the wash with less “workload”.
Modern washers are equipped with special sensors that monitor the weight: when it is exceeded, they stop the process. On some models, this information is displayed.
Do not forget to check the external conditions that affect the operation of the machine. Some washers are equipped with sensors that are sensitive to water pressure.
While the user disassembles the device and changes the details, the clamped hose, a bursting gasket or a dirty filter will not inform themselves to attract attention.
What malfunctions lead to the problem?
Breakdowns in the machine are divided into rare and typical. The drum stop belongs to the second group. The causes of damage can be mechanical, technical, domestic problems.
If the washer worked for a long time within its capabilities and without proper preventive maintenance, technical malfunctions appear. They require specialist intervention. You can handle the rest on your own.
Breakage # 1 - foreign object in the tank
Take a flashlight, inspect the drum from the inside. It is important to carefully examine everything to see if a foreign object is found there.
A common option is a bone that has fallen into the hole from a bra. If this problem is found, carefully remove the bone with a pair of pliers. Be careful not to break it
We get other foreign objects:
- Extend the machine to allow access from all directions.
- Remove the bolts on the rear panel that hold the top cover.
- Slide the cover back to remove it.
- Loosen the screws of the back cover, remove it.
- Get the heater, this will facilitate the process of extracting foreign objects.
- Separate the wires that go to the heating element, unscrew the fixing nut. The heating element can be easily pulled out if picked up with a screwdriver.
- It turned out a hole - we shine a flashlight into it.
- Did you see the problem? We twist a wire of sufficient length, we get out with it the stuck object.
- We install the heater in place, we monitor the excellent landing density, we tighten the nut.
- We collect the machine.
When an object is located in the space between the drum and the tank from above, it cannot be seen through the heater hole.
If you can’t see anything through the hole in the mounting of the heater, try spinning the drum and objects stuck on top will drop down
We lock the pulley with a block of wood, unscrew the fixing bolt, remove the pulley, fasten the bolt, but not completely. Now hit the bolt with a hammer, try to keep the thread.
After removing the pulley and screwing the bolt, substitute a wooden board between the hammer and the bolt to soften the blows and not break the thread
As a result of the blows, the shaft and the drum will slightly move forward, and the excess object will go down, where it is convenient to get it. Return the pulley in place, fasten the bolt until it stops. We install the back wall of the machine, we fix all the bolts.
Breakage # 2 - the sash in the vertical opened
In vertical typewriters, the tank flaps are often opened during the spin cycle. The reason is sometimes not related to a leaking latch.
Perhaps too smart a child got and cranked the drum with the wings open. Or an adult has loaded too much laundry and a piece of cloth has landed on the latch.
The metal wings are closed by a sufficiently reliable special latch, but it tends to wear out over time, to become loose, which leads to the opening
The problem does not look serious. But the severity of the consequences depends on the moment when the sash was opened. If on a delicate wash, in most cases, nothing bad happens.
But during a strong spin, open blades can turn into meat grinder knives and spoil everything that gets in the way.
The flaps penetrate the protective barrier at speed. The heater is the first to be hit, for the company the walls of the tank itself and the drum leaf are damaged. When all three elements break down, repairs are expensive. Cheaper to buy a new washing machine.
Let's try to solve the problem differently. You need to try with minimal effort and carefully return the drum to its original position.
If it doesn’t work, try closing the sash. You will need a strong, elastic steel wire with a diameter so that it passes into the holes of the drum.
If the warranty for the washing machine has already expired, you can slightly open one of the holes in the drum to make it easier to manipulate the closing of the wings
Bend the end of the wire with a pair of pliers about half a centimeter to form a hook. Carefully push it into the hole. Using a flashlight in one hand and a wire in the other, we try to close the wings.
If possible, you will be able to scroll the drum. When the wire cannot catch the sashes or they cannot be held in rotation and they still open, you will have to disassemble the washer.
When disassembling, do not lay the machine on its side, just tilt it: there are always water residues in it that can spill onto the parts of the mechanism
General procedure:
- We unscrew the latches of the rear panel, set it aside.
- We shift the sidewall to the side, we also remove it.
- We photograph the location of the wires, disconnect them.
- Unscrew the screw holding the shaft.
- Close the loading door, get the tank.
- Separate the halves of the tank, get the drum.
- We clean parts from dirt and debris.
Now try to close the sash several times. If the lock is broken, this part can be ordered from the manufacturer and replaced.
We examine the flaps themselves, the integrity of the tank, damage to the heating element. Significant deformations are an occasion to think about buying a new washing machine.
Failure # 3 - jammed rusted bearing
Bearing wear is another malfunction that causes the drum to stop. We have it disassembled, check the bearing. Carefully knock out the part with an improvised tool.
In addition to the bearing itself, the oil seals must be replaced. The bearing mounting location is treated with lithol, we return the elements back. Fasten with a hammer.
The average life of these parts is 7 years, after which they need to be completely replaced, otherwise there will be problems when washing
If you have a horizontal machine, the procedure is as follows:
- Unscrew the fasteners, remove the back and top cover.
- Dismantle the dispenser.
- We remove the control unit, having previously unscrewed the latches.
- We open the loading hatch, we turn out the rubber cuff, we fill it into the drum.
- We remove the lock.
- We remove all fasteners, remove the front panel.
- Weaken the clamp, remove the counterweight.
- Now you need to pull out the heater. Here we pay attention to the order of connecting the wires, turn them off, pull out the heating element.
- We remove all remaining obstacles that connect the tank and the body - pipes, drive.
- Turn off and get the engine.
- After that, nothing prevents removing the tank with the drum.
To make it more convenient to work, the tank can be moved to a solid table. Next, we do everything similarly to the algorithm with a vertical machine: knock out the bearing, remove the seals, lubricate the socket, install new parts.
When assembling the drum, perform the installation very carefully. Seal the joint with a sealant to avoid leaks. There are models of cars with non-collapsible tanks, it is reasonable to entrust their repair to the master.
Detailed instructions for replacing bearings in the washing machine are given in this material.
Failure # 4 - the drive belt has flown or damaged
Remove the rear panel of the machine, look at the condition of the belt. If it just slipped, put it back in place, close the lid, turn on the washer and check if it works. In the event of complete wear, damage will require replacement.
On machines with asynchronous motors, V-belts are V-belts, and with collector ones, V-belts. The first in the section are trapezoidal, are marked on the outside. This is exactly what is shown in the figure
They are made of chloroprene rubbers, polyester cords, cotton material, due to which they are elastic and have increased strength characteristics.
The V-belt is pulled, moving the engine, so you need to loosen the fasteners. When the adjusting stroke of the engine is small or such a maneuver is excluded by the design of the machine, the belt must be replaced.
We install the V-belt like this: wrap it on a pulley, then put the strip in the drum groove and completely seat it there, rotating the pulley.
In the figure, the arrows indicate the belt. The tension of the V-belt should be very tight: if you press firmly in the middle, a deflection of up to 5 mm is considered normal
The V-ribbed belt has a gear section. Parameters are also marked on the outside. It changes in the same way as a wedge. But he needs careful position control after the final installation.
We measure the middle of the reciprocal part of the engine and drum pulley - the belt is installed strictly along this line. V-ribbed belts stretch less than V-belts.
We also recommend that you read the detailed instructions for selecting and replacing the belt in the washer.
Breakage # 5 - worn motor brushes
When worn brushes do not provide the desired electromagnetic field, the motor rotor stops rotating. During the operation of the washer, this part is shortened and the collector is no longer available. Need a replacement.
Be sure to buy two identical ones that correspond to your model and without brush defects: installation of parts with different stiffness threatens engine failure
If the machine is assembled, remove the back wall, belt. We disconnect the engine from the power by pulling out the connector with wires. We dismantle the engine itself.
Next, we lay the engine on its side so that the brush body is on top, and unscrew the mounting bolts, pull out the spare part on one side and the other.
Usually brushes last for 6-8 years. Service life depends on the frequency of operation of the machine, compliance with recommendations for loading the drum, assembly quality of the unit
Do not rush to change, inspect the elements. Measure the rods: if their length exceeds 1.5 cm, the brushes do not cause the drum to stop.
Also, do not forget to clean the collector from black deposits; remove scratches with sandpaper. That's it, now you can put new elements and tighten them with bolts.
Breakdown # 6 - the control module is broken
The drum may remain stationary due to the lack of a signal from the "brain" to start washing. Most often, the control board fails due to voltage surges or natural wear.
There are three solutions to the problem - to reset the programs, “flashing” or replacing the module.
Some models have a self-test function. It allows you to determine the source of the problem. How to enable this feature? They do not write in the instructions, but the starting method depends on the manufacturer and the specific model.
As an example - Ardo it is tested like this: we drain the water, the tank should be empty, set the mechanical program switch vertically down, set the temperature to zero. To start the test mode, click on all buttons at once.
Each machine has its own way to enable auto-test: LG - by pressing the power, temperature, spin keys, and then you need to press the start one time three times to test the operation of the drum
If you still need to remove the board, it is removed quite simply. We remove the upper panel, dismantle the upper part of the machine, remove the fixing strips and remove the module.
Repair of the control unit requires special skills - you need to check the parameters of the elements, track the chain. We carefully inspect the board.
Remove the fee yourself only after the warranty period has expired, and if there are no skills for such repairs, you can replace the entire control unit
4 signs of the need for serious intervention:
- The tracks darkened, the color changed in some places, tan marks appeared.
- The bulges on the caps of the capacitors are visible.
- Burned varnish on damping coils.
- The main processor darkened at the installation site.
If any of the above is found and there is no experience with a soldering iron, multimeter, entrust the repair to a specialist.
Failures related to sensor problems can be fixed on their own. Contact groups become greasy and clogged over time, they just need to be cleaned. Remove the program knob, disassemble the handle and clean it.
If there is a soot layer on the power coils of the line filter, brush it off with a dry cloth and brush. The block of the hatch lock is exempt from soapy plaque.
Failure # 7 - engine burned out
The motor is usually reliable and you need to try very hard to break it. But there are a couple of cases when this happens. The winding closes or breaks at the stator and rotor.
A characteristic sign of the first situation is that an empty drum spins normally, and with full washing, traffic jams break out. When a second situation occurs, the drum stops rotating at all.
Repair is possible if the drum has stopped, but the included machine is buzzing. A complete engine replacement is needed when there is no start at all, it smells of burning, there is dark smoke, the washing machine sparks. To begin, remove the electric motor, see what can be done.
The fastener systems in different models are different, but there is one principle - holding bolts must be removed. Also do not forget to disconnect the motor power terminals. The figure shows the bolts
The motor is removed in the same way as when replacing the belt. If it is clamped by the tank, slightly raise the tank and release the engine. Sometimes you have to remove the side wall. There are three main faults - brushes, lamellas, windings.
How to replace the brushes, we have already considered. The windings can be tested with a multimeter when probing adjacent lamellas alternately. The discrepancy should be less than 5 ohms.
We also check the closure of all the windings: we place one probe on the case, and the second we go through the lamellas.If everything is OK, the resistance will be high.
It is simple to determine the unsuitability of the lamellas - we completely remove the rotor from the engine, inspect the collector for burrs, peeling, contact breaks
If the windings are faulty, it is better to find the same part and replace it. Rewinding will cost more. Slight delamination of the lamellas can be machined on a lathe.
But such an event will not become a panacea; the factory look and quality cannot be returned to them. Conclusion: we change the details to new ones.
Future Prevention Techniques
Empty pockets thoroughly before washing. Load all the little things (baby socks, handkerchiefs) and bras in special mesh bags.
It is important not to overfill the tank - follow the manufacturer's recommendations on the maximum weight of the laundry, do not fill the machine to the limit
Connect the washer through an uninterruptible power supply or at least an extension cord with a differential lock if you live outside the city or simply have problems with power surges.
This is especially true for models with many programs and too clever “brains”. Pay attention to the correct grounding of the machine.
In addition, it is necessary to regularly carry out preventive cleaning of the drum - this will protect the washing machine from breakdowns and the occurrence of unpleasant odors.
More details about repairing faults can be found in the videos presented by the service center masters and ordinary users.
Front-loading machine disassembly diagram:
Removing and opening the washing drum is considered in the following video:
When you change everything, install, close the machine, be sure to check the performance of the equipment. Run your regular program. The wash runs in the usual mode or sounds louder than usual - order, everything is done correctly. Creaking, chattering, too loud noise of the washing machine - an occasion to seek help from a service center.
Had to face a problem when the drum of the washing machine stopped spinning? Please tell us how you managed to deal with this problem, what caused it. Write your comments, share your experience, ask questions - the contact block is located under the article.